Vol 39, No 2 (2011): Hungarian Journal of Industrial Chemistry

View Vol 39, No 2 (2011): Hungarian Journal of Industrial Chemistry
Published: 2011-09-01

Articles

  • Investigation of Sensible Heat Storage and Heat Insulation in the Exploitation of Concentrated Solar Energy

    DOI: https://doi.org/10.1515/403
    I. Árpád
    163-167

  • Control Operation and Analysis of the Spur Gears Profile

    DOI: https://doi.org/10.1515/404
    E. Faluvegi, L. Cristea
    169-172

  • Connection Theory of Conical Worm Gear Drives

    DOI: https://doi.org/10.1515/405
    S. Bodzás, I. Dudás
    173-176

  • The Attendance of Rational Energy Utilization and of the Green Energy

    DOI: https://doi.org/10.1515/406
    A. Farkas, P. Faragó
    177-181

  • Enhanced Use of Renewable Resources: Transesterification of Glycerol,the Byproduct of Biodiesel Production

    DOI: https://doi.org/10.1515/407
    Z. Herseczki, G. Marton, T. Varga
    183-187

  • Method for Determination of the Expected Roughness of Cut Surfaces

    DOI: https://doi.org/10.1515/408
    C. Felho, J. Kundrak
    189-193

  • Performance Evaluation of Bitumens at High Temperature with Multiple Stress Creep Recovery Test

    DOI: https://doi.org/10.1515/409
    K. Adorjányi, P. Füleki
    195-199

  • Examination Possibilities of Waste Water Purification Originate from Animal Waste Process

    DOI: https://doi.org/10.1515/410
    G. Gulyás, Á. Kárpáti
    201-204

  • Experimental Results of Dry Drilling of Wear Resistant Steel

    DOI: https://doi.org/10.1515/411
    A. Kovács, Gy. Varga
    205-210

  • Cutting of Aluminium Alloy by Abrasive Waterjet

    DOI: https://doi.org/10.1515/412
    K. Kun-Bodnár, Zs. Maros
    211-214

  • Using Graphical Processing Units in Scheduling Problems

    DOI: https://doi.org/10.1515/413
    K. Mihály, O. Hornyák
    215-218

  • Comparison of Hard Machining Procedures on Material Removal Rate

    DOI: https://doi.org/10.1515/414
    V. Molnar, J. Kundrak
    219-224

  • Finite Element Method Analysis of Hip-Joint Prosthesis

    DOI: https://doi.org/10.1515/415
    R. Monostori, I. Dudás
    225-227

  • On-Board Applicability of Mems-Based Autonomous Navigation System on Agricultural Aircrafts

    DOI: https://doi.org/10.1515/416
    P. Nádasi, I. Szabó
    229-232

  • Determination of the Inductance of Starter Relays

    DOI: https://doi.org/10.1515/417
    L. Nagy, J. Lénárt, E. Jakab
    233-235

  • Prototype of a Multi-Robot System for Autonomous Gas Mapping in Polluted Environments

    DOI: https://doi.org/10.1515/418
    D. Lupea, I. Szőke, A. Majdik, Gh. Lazea
    237-242

  • ‘By’ Treating of Micro-Alloyed Steels Supported by Integrated ‘IT’ Technology in the Forging Factory of Raba

    DOI: https://doi.org/10.1515/419
    F. Tancsics
    243-249

  • Optimalisation the Position of Solar Cells for Vehicles

    DOI: https://doi.org/10.1515/420
    I. Lőrincz, D. Czeglédi
    251-255

  • Optimal Tool Selection for Environmental-Friendly Turning Operation of Aluminium

    DOI: https://doi.org/10.1515/421
    R. Horvath, B. Palásti-Kovács, S. Sipos
    257-263

  • Comparison of Scalar and Vector Control Strategies of Induction Motors

    DOI: https://doi.org/10.1515/422
    G. Kohlrusz, D. Fodor
    265-270

  • Heavy Metal Contamination Assessment and its Environmental Impact in the Area of Rural Waste Disposals in Cluj County,Romania

    DOI: https://doi.org/10.1515/423
    G. Popiţa, I. Varga, C. Modoi, R. Haţegan, A. Popovici
    271-278

  • CBN Tool Life Prediction by Artificial Neural Network

    DOI: https://doi.org/10.1515/424
    L. Raczkovi
    279-282

  • Removal of Hydrogen Sulfide from Natural gas,a Motor Vehicle Fuel

    DOI: https://doi.org/10.1515/425
    Á. Vágó, D. Rippel-Pethő, G. Horváth, I. Tóth, K. Oláh
    283-287

  • Investigation on Coherencies between Residual Stresses and Tool Geometry by Hard Turning

    DOI: https://doi.org/10.1515/426
    G. Szabo, J. Kundrak
    289-294

  • Separation of Multicomponent Mixtures

    DOI: https://doi.org/10.1515/427
    L. Szabó, S. Németh, F. Szeifert
    295-300

  • The Region of Sebes-Körös and Holt-Sebes-Körös as Sample Areas of the Water Framework Directive

    DOI: https://doi.org/10.1515/428
    Cs. Szalkay
    301-303

  • Development of a Vehicle-Dynamic Measurement and Information System

    DOI: https://doi.org/10.1515/429
    F. Szauter, J. Á. Székely, E. Horváth
    305-308

  • Rotational Turning in Precision Finishing

    DOI: https://doi.org/10.1515/430
    I. Sztankovics
    309-312

  • Seasonal Changes in Weed Vegetation on Arable Pannonian Sand and Loess Lands in Hungary

    DOI: https://doi.org/10.1515/431
    A. Tóth, Á. Balogh, B. Wichmann, I. Dancza, Cs. Szalkay, K. Penksza
    313-315

  • Efficiency and Mass Optimization of Electric Permanent Magnet Motor Driven Vehicle

    DOI: https://doi.org/10.1515/432
    J. Polák
    317-320

  • Bioethanol Production from Paper Sludge Pretreated by Subcritical Water

    DOI: https://doi.org/10.1515/433
    N. Pézsa, P. Ailer
    321-324

  • Thoughts about the Clear Energy

    DOI: https://doi.org/10.1515/434
    A. Farkas, P. Faragó
    325-330